Johns Manville R13 Insulation 15 x 93 Paper-Faced Fiberglass Batt
JM Unfaced Formaldehyde-free ™ fiberglass insulation is perfect for effective thermal as well as sound control. Our unfaced insulation is offered in pre-cut batts to fit standard wall and ceiling areas. Enhance the general efficiency of your home with fiberglass wall insulation. It’s thermal efficiency assists to keep temperatures down, reducing power loss and power prices while likewise minimizing room-to-room noise transmission.
- Pre-cut and Easy to Install
- Formaldehyde-free: Greenguard GOLD certified & SCS Certified to be formaldehyde free
- Sound Control: Reduces sound transmission through exterior and interior walls, floor and ceiling assemblies.
- Thermally Efficient: Effective resistance to heat transfer
- Moisture Control: Kraft facings provide excellent vapor retarders
- 106.5 Square Feet per Bag
- Fiberglass Insulation Batt 15 in. x 93 in. x 3.5 in. thick
- Easy Installation – These batts are easy to handle and friction fit in cavities.
- 5 bags per Master Pack
- 11 Pieces per bag
Johns Manville Unfaced Fiberglass Batt insulation is Made in the USA. All batts are precut to friction fit into basic wall and ceiling bays. Established in 1858, Johns Manville is one of the finest and most offered fiberglass insulation product in the USA.
Johns Manville makes eco-freindly formaldehyde free fiberglass. They make fiberglass insulation for the house as well as industrial applications from R11,R13,R15,R19,R21,R25,R30,R38 and R49. JM gives quality insulation for noise, thermal and also power conserving remedies for todays houses.
Insulating Walls with Fiberglass
When you are insulating two-by-four) as well as 2×6 framed outside walls and intend to use fiberglass insulation, what density is recommended? The concern becomes all more vital due to the irreversible nature of wall cavity assembly as well as wall cavity insulation: Once the insulation is installed the wall and also sealed up with drywall, it is challenging to swap out.
When you add inadequate insulation, you will certainly have a cooler residence. However installing too much insulation– packing in more than is needed– can likewise result in a chillier residence than is needed. Tiny air pockets produced within the insulation are what help maintain a residence warm and also cozy, not the actual hairs of fiberglass or paper kraft facing. Striking the best equilibrium between insufficient insulation and also excessive insulation will certainly keep you and your family warm throughout the wintertime.
Essentials of Kraft Faced Fiberglass Insulation, From R Thirteen to R Nineteen
R-value is a typical system of measurement for figuring out, amongst several things, just how efficient your insulation will be. The R describes outright thermal resistance. Higher R-value numbers imply that the insulating product resists the cold or warm from the outdoors better. Density, how wide, and also composition of products are some variables that contribute to R-value.
Insulation for Two by Four Walls
The majority of wall cavity assemblies, particularly those in older residences, are constructed with two-by-four (2×4) studs. Considering that contemporary two-by-fours are not 4 inches, the true depth of the wall bay is 3 1/2 “.
In a lot of wall cavity applications, you will use R-13 or R-15 kraft-faced fiberglass precut batts for these two-by-four stud walls. While rated differently, these 2 kinds of insulation are close enough in density that they can both match modern-day two-by-four wall cavity systems. With R15 being a high density product, it is far superior for sound deadening. However will cost you about 70 percent more than R 13.
Older homes, especially those pre-dating the 1950s, may utilize two-by-fours that absolutely are 2 inches by 4 inches. In this situation, you can still use R-13 or R-15 fiberglass insulation. There is no 4-inch deep faced fiberglass insulation in batts or rolls on the open market.
Insulation for 2×6 Studs
Some newer homes might have walls built with 2×6 studs. You should consider R-19 or R-21 kraft-faced fiberglass insulation for 2 by 6 wall studs. This mix makes sure that the insulation is neither too loose neither too firmly compressed within the wall cavity.
JM insulation is offered in big box shops and likewise can be bought through representatives like Pacific Insulation. Pacific Insulation gives an unique opportunity to buy the same products at store at wholesale prices. House owner and also service providers have the possibility to purchase little or huge amounts straight type the supplier. By purchasing straight we are able to provide reduced prices do to reduced operating costs. Customers can grab from among our 70 locations or we can supply direct to job websites.
Rates can differ by area in the United States. Its always best to message or call us to get a specific quote fo the specific quantity of fiberglass insulation that you require.
2008 U.S. Department of Energy
R-Value Recommendations for New and Existing Homes
The following 2008 Department of Energy zone recommendations are based on comparing estimated future energy savings to the current cost of installing insulation. The DOE gives a range for many locations for the following reasons:
- Energy costs vary greatly over each zone
- Installed insulation costs vary greatly over each zone
- Heating and cooling equipment efficiency varies from house to house
- Best estimate of future energy costs may not be exact. 1
- Reference : Department of Energy Insulation Fact Sheet
(DOE/CE-0180 2008 update) DOE/CE-0180 2008, Insulation Fact Sheet.
JM InsCall Us Now (424)343-6530 or Message Us Now for bulk pricing.